The SP3000 tester has a universal base test engine. With the correct test adapter, you can configure it to test both DRAM and SDRAM memory.
The Combo Tester option includes a base tester and two test adapters. The DRAM test adapter test 72pin SIMM and 168 pin DRAM DIMM. It is capable of testing JEDEC standard 72pin EDO and Fast Page & 168pin EDO & FPM DIMM module. The SDRAM test adapter test JEDEC standard 168pin SDRAM PC133 PC100 PC66 unbuffered and RegisteredSDRAM DIMM memory modules at real frequency. Optioinal 30pin SIMM and 144pin SDRAM SODIMM for laptop can be added too.
The SP3000 tester has user selectable test option. For Basic Test, it checks for assembly open and shorts on the module using the Walk address and Walk data test patterns. For detail comprehensive testing, the tester has additional user definable patterns such as Marching, Checkerboard , Preheat, Burst, Voltage Bounce tests to check for dram cell and operations related faults.
For DRAM module testing
Walk Address Test - checks for open/short on address pins and bad address decoder.
Walk Data Test - checks for open/short data bits
Marching & Checkerboard Test checks for bad cells, decoder interaction problem.
Pre-heat Test checks for reliability during chip warming up.
Voltage bouncing test checks for modules with noise related problem
Loop Test to simulate module burn-in situation
For SDRAM Testing:
Has similar test as above and includes the followings :
Burst Test – checks for faulty chip that fail to read&write during consecutive clock cycles.
Chip Select Test – checks for assembly shorts and open on the CS pins
DQM Test – checks for SDRAM chip input and output masking ability
WP Test – check for module that is PC-100/PC133 Intel compliance.
The tester detects almost all faults associated with memory module. The tester has an access time (Speed) resolution of 1 nanosecond and It is the tester used by majority of SIMM Module memory manufacturers and Service Depot.
The SP3000 is able to test a 32MB – 168pin DRAM DIMM module in 2 seconds for quick test (open and short test).A comprehensive detail test (open/short, marching test ) will take under 10 sec to complete . This is the fastest tester compared to other testers that will take 25 sec.
The SDRAM-133Mhz test adapter can perform a detailed test on a 32Mb PC100 SDRAM DIMM module in less than 8 sec flat as compared to other tester that will take more than 20sec.
With the correct test adapter attached to the base unit, you will be able to detect an entire array of memory module for size, number of data bits, access time (speed) etc. There's no guess work on your part. The SP3000 will Automatically-Identify all JEDEC standard module, for size/capacity, device configuration, access time (speed), parity / non parity/ ECC /3.3V/5.0V voltages and more.
Yes, with the SDRAM 133mhz test adapter, it has user selectable frequency option from 66mhz - 133mhz to test PC133 PC100, PC66 SDRAM DIMM module. If you do not know the frequency, do not worry! The tester can automatically detects the frequency for you too!
The SP3000 is the most preferred tester used by many SIMM/DIMM manufacturer / OEM and Service Depot customer such as Samsung, HP, Micron, Compaq, Dell, CompUSA, Frys and more..
The SP3000 won the Reader ‘s Choice Award for Best Low Cost ATE Tester Solution in EE magazine (Evaluation Engineering)
The SP3000 is very easy to upgrade with optional plug-on test adapters.
Field upgradable with easy PC Control and Free Firmware download from the Internet.
User friendly test menu for “non –technical user”.
Compact, portable and standalone with universal switching power supply.
For Hardware upgrade to a different memory module type testing, the tester can be easily configured by purchasing the appropriate plug-on test adapter to the base tester.
For Firmware upgrade, an optional PC Interface Kit is available which allows user to download the firmware directly into the tester at the convenience at your location.
No, the tester is designed as a complete standalone unit and connection to PC is easily available with an optional PC Interface Kit & software. The PC will provide enhanced display of results & allow on-line firmware upgrade for future revision change
Yes , the SP3000 has a printer port located at the rear of the tester, it can be connected to any printer directly with a printer cable. The fail results will be printed out upon enabling the print function.
SP3000 SDRAM Version 1xx
Module : SD 2Mx64-8ns 2Kref# 1B (2) 3.3V
Addr. ( row x col.) : 11 x 9
Data (bank x bit) : 1 x 64 (2)
Test Pattern : w_addr, w_data, march, chk_bd
Loop # : 1
## FAIL : Walk Data - Loop 1 ##
Bank 1 : 1- 9, 11, 13, 15, 17, 19,
21, 23, 25, 27, 29, 31-3
Yes, the SP3000 is capable of testing Notebook memory modules. Two Version of the notebook adapter are available, one on the DRAM SODIMM and another for SDRAM SODIMM.
For DRAM 72 pin SODIMM and 144 pin SODIMM module, user will require the SP3-72/144 pin SODIMM DRAM adapter.
For SDRAM 144pin SODIMM, user will require the SP3-144/168 pin SDRAM adapter.
For PCMCIA Dram card module, user will require the SP3-PCMCIA Card Adapter.